21. The starting torque of a D.C. motor is independent of which of the following?
(a) Flux
(b) Armature current
(c) Flux and armature current
(d) Speed
Ans: d
22. Rotor of a motor is usually supported on _______ bearings.
(a) ball or roller
(b) needle
(c) bush
(d) thrust
Ans: a
23. For which of the following applications D.C. motors are still preferred ?
(a) High efficiency operation
(b) Reversibility
(c) Variable speed drive
(d) High starting torque
Ans: c
24. In a paper mill where constant speed is required
(a) synchronous motors are preferred
(b) A.C. motors are preferred
(c) individual drive is preferred
(d) group drive is preferred
Ans: c
25. A reluctance motor
(a) is provided with slip rings
(b) requires starting gear
(c) has high cost
(d) is compact
Ans: d
26. The size of an excavator is usually expressed in terms of
(a) 'crowd' motion
(b) angle of swing
(c) cubic metres
(d) travel in metres
Ans: c
27. For blowers which of the following motor is preferred ?
(a) D.C. series motor
(b) D.C. shunt motor
(c) Squirrel cage induction motor
(d) Wound rotor induction motor
Ans: b
28. Belted slip ring induction motor is almost invariably used for
(a) water pumps
(b) jaw crushers
(c) centrifugal blowers
(d) none of the above
Ans: b
29. Which of the following is essentially needed while selecting a motor ?
(a) Pulley
(b) Starter
(c) Foundation pedal
(d) Bearings
Ans: b
30. Reluctance motor is a
(a) variable torque motor
(b) low torque variable speed motor
(c) self starting type synchronous motor
(d) low noise, slow speed motor
Ans: c
Read More Questions:
Industrial Drives MCQs Part1
Industrial Drives MCQs Part2
(a) Flux
(b) Armature current
(c) Flux and armature current
(d) Speed
Ans: d
22. Rotor of a motor is usually supported on _______ bearings.
(a) ball or roller
(b) needle
(c) bush
(d) thrust
Ans: a
23. For which of the following applications D.C. motors are still preferred ?
(a) High efficiency operation
(b) Reversibility
(c) Variable speed drive
(d) High starting torque
Ans: c
24. In a paper mill where constant speed is required
(a) synchronous motors are preferred
(b) A.C. motors are preferred
(c) individual drive is preferred
(d) group drive is preferred
Ans: c
25. A reluctance motor
(a) is provided with slip rings
(b) requires starting gear
(c) has high cost
(d) is compact
Ans: d
26. The size of an excavator is usually expressed in terms of
(a) 'crowd' motion
(b) angle of swing
(c) cubic metres
(d) travel in metres
Ans: c
27. For blowers which of the following motor is preferred ?
(a) D.C. series motor
(b) D.C. shunt motor
(c) Squirrel cage induction motor
(d) Wound rotor induction motor
Ans: b
28. Belted slip ring induction motor is almost invariably used for
(a) water pumps
(b) jaw crushers
(c) centrifugal blowers
(d) none of the above
Ans: b
29. Which of the following is essentially needed while selecting a motor ?
(a) Pulley
(b) Starter
(c) Foundation pedal
(d) Bearings
Ans: b
30. Reluctance motor is a
(a) variable torque motor
(b) low torque variable speed motor
(c) self starting type synchronous motor
(d) low noise, slow speed motor
Ans: c
Read More Questions:
Industrial Drives MCQs Part1
Industrial Drives MCQs Part2
No comments:
Post a Comment